Undersink Twin 10 inch standard housing with Fluoride filter and Carbon filter
$339.00
Pentek 10″ inch standard slim line Housing with 1/4″ NPT thread ports.
Rugged design reinforced polypropylene for increased strength and durability.
Comes with:
Starter Filters – Fluoride Removal and Carbon Chlorine & Contaminant filters (1 of each)
Your choice of: – Take Off Valve type, and Tap style type
Tap: Platinum Single Lever Tap
Not included: Pressure Reducing Valve, PRV PLV, are not included.
| 1 | 2 | 3 | 4-5 | 6+ |
| $339.00 | $328.83 | $327.14 | $325.44 | $322.05 |
Pentek Twin 10 inch standard slim line housing, 1/4 inch NPT ports.
Reinforced polypropylene housing cap molded from rugged reinforced
polypropylene and offer outstanding chemical compatibility.
They are ideal for use in a variety of low-flow applications.
It is constructed totally from FDA grade materials and media
Should be used in conjunction with Pressure Reducing Pressure Limiting valve (not included).
Comes complete with:
Starter Filter Pair.
Your choice of Take-Off Valve
Your choice of Tap
Fluoride and Arsenic reduction Cartridge, Activated Aluminium AAL
1st stage Activated Aluminium cartridge for fluoride reduction
Designed to reduce fluorides to below 0.5 ppm.
High pH, high bicarbonate levels and high flow rates all adversely affect the capacity of the AAL
Carbon Filter
2nd stage CBC-10 carbon filter for Chlorine and other contaminant reduction
10″ Pentair CBC-10 Carbon Block Cartridge 0.5 Micron (10″ x 2½”)
TAP options:
- Platinum Single Lever Tap, PLAT-S, Or
- Designer Tap, TAP-D
Take Off Valve Options:
Please advise which tap and take-off valve when ordering undersink kits.
- Plumbers Delight Take-off Valve – SV5 (1/2″ BSP MF) w 1/4″ take-off – used for installations with 15mm (½”) BSP connections
- Saddle Valve 6 – G Clamp, used with Polybutylene, w 1/4″ take-off
- SV3 Saddle Valve – Parallel, used with Metal Piping, w 1/4″ take-off
- Dish Washer Take Off (Capped) – 20mm Female with 1/4″ BSP
- Dish Washer Tap – Take Off Tee – 20mm MF w/1/4″ BSP
Pentair Pentek Twin 10 inch slim line housing, 1/4 inch NPT ports Features:
- 1/4″ NPT female ports
- Twin 10 inch Housing suitable for low flow situations
- Rugged design for strength and durability
- Leak proof seal
- ANSI/NSF Tested and Certified Materials
- Will accomodate standard 10″ housing cartridges
Pentair Pentek Twin 10 inch slim line housing, 1/4 inch NPT port Specifications:
- Single Product part code: 158179
- Max pressure 100 psi
- Pressure rating: 100 psi (6.9 bar)
- Temperature rating: 4.4-37.8°C (40-100°F)
- Maximum Flow Rate : 10″: 75 LPM
It the pressure will at any time exceed the maximum rating then a pressure regulator must be installed before the filter housing (set at 75 PSI or less)
To prevent leaking, o-ring must be in good condition, properly lubricated and seated in the groove of the sump.
Do not over-tighten sumps; hand tighten only.
Product complies with Australian Watermark Certification.
This housing is suitable for filter sizing of 10” big/jumbo with 4½” diameter.
